Try JN0-363 Exam Valid Dumps with Instant Download Free Updates
JN0-363 Dumps First Attempt Guaranteed Success
Juniper JN0-363 exam is a certification program that validates the knowledge and skills of individuals in the field of Service Provider Routing and Switching. JN0-363 exam is designed to test the candidates' ability to configure, monitor, and troubleshoot Juniper Networks routing and switching devices in a service provider environment. The JN0-363 exam is one of the three exams required to earn the Juniper Networks Certified Internet Specialist (JNCIS-SP) certification.
The JNCIS-SP Certification is a valuable credential for networking professionals who work in service provider environments. It demonstrates a high level of expertise in Junos software and service provider routing and switching technologies. Service Provider Routing and Switching, Specialist (JNCIS-SP) certification can lead to career advancement opportunities, such as senior network engineer or network architect roles.
NEW QUESTION # 99
Exhibit
Which two statements ate correct about the actions taken as the packet traverses the service provider MPLS network from Site 1 to Site 2 as shown in the exhibit? (Choose two.)
- A. R2 will perform a lookup using the inet.3 table.
- B. R1 will perform a lookup using the mpls.0 table.
- C. R1 will perform a lookup using the lnet.3 table.
- D. R2 will perform a lookup using the mpls.0 table.
Answer: D
NEW QUESTION # 100
You have two MX Series devices connected together and configured for Layer 2 operations. The interface that connects the two routers must carry tagged and untagged traffic.
Which approach would meet this objective?
- A. Configure the interfaces as access ports with the voice VLAN option
- B. Configure the interfaces as trunk ports with the voice VLAN option
- C. Configure the interfaces as trunk ports with the native VLAN option
- D. Configure the interfaces as access ports with the native VLAN option
Answer: C
NEW QUESTION # 101
Which two statements are correct about the way that BGP propagates routes by default? (Choose two.)
- A. A route learned by IBGP will not be re-advertised lo IBGP peers.
- B. A route learned by IBGP will be re-advertised to IBGP peers.
- C. A route learned by EBGP will be re-advertised to IBGP peers.
- D. A route learned by EBGP will not be re-advertised to IBGP peers.
Answer: B,D
NEW QUESTION # 102
Click the Exhibit button. After the MAC learning limit of 3000 is reached for the bd bridge domain as shown in the exhibit, what happens to frames that arrive that contain unknown unicast destination addresses?
- A. They are forwarded to the IRB interface.
- B. They are dropped.
- C. The are forwarded to the default gateway.
- D. They are flooded.
Answer: D
NEW QUESTION # 103
Exhibit
You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.
Which two tasks will accomplish your objective? (Choose two.)
- A. issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.
- B. Under the [edit routing-options] hierarchy, configure a 32-bit router ID.
- C. Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.
- D. Under the [edit routing-options] hierarchy, configure a 128-bit router ID.
Answer: A,B
Explanation:
To configure OSPFv3 (the version of OSPF that supports IPv6), you would use theset protocols ospf3 command with the appropriate area and interface. OSPFv3 requires a 32-bit router ID just like OSPFv2, which is typically an IPv4 address. OSPF does not use a 128-bit router ID, so answer D is incorrect.
References:
Juniper Networks documentation on OSPFv3: OSPFv3 Overview
NEW QUESTION # 104
Which two statements are correct about IS-IS? (Choose two.)
- A. A level 1 only router can never form an adjacency with a level 2 only router.
- B. A level 1 only router can form an adjacency with a level 2 only router.
- C. For level 2 adjacencies, the area IDs can be different.
- D. For level 2 adjacencies, the area IDs must be the same.
Answer: A,C
Explanation:
A Level 1 router can become adjacent with the Level 1 and Level 1-2 (L1/L2) router. A Level 2 router can become adjacent with Level 2 or Level 1-2 (L1/L2) router. There is no adjacency between L1 only and L2 only router. HOWEVER: If two routers are in different areas, they can only form a Level 2 adjacency. As such, two routers in different areas can NOT form a Level 1 adjacency. If you want two routers to form a Level 1 adjacency, they have to be in the same area.
NEW QUESTION # 105
Click the Exhibit button. Given the OSPF network topology shown in the exhibit, you would like to inject external (non- OSPF) routes into the network on Router D
Which two OSPF area types will support this configuration? (Choose two)
- A. not-so-stubby area
- B. non-backbone area
- C. totally stubby area
- D. stub area
Answer: A,B
NEW QUESTION # 106
Referring to the exhibit, what is the minimum number of LSPs required to support alt four networks?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 107
Click the Exhibit button. In the exhibit, all routers are sending routes to Router B
Which routes will be advertised from Router B to Router D?
- A. BGP routes learned from Router E only
- B. BGP routes learned from Router A only
- C. BGP routes learned from Routers A and C only
- D. BGP routes learned from Routers A, C and E only
Answer: D
NEW QUESTION # 108
Exhibit
Routers R1 and R4 have a VRRP priority of 90, while R2 and R3 have default VRRP priorities Referring to the exhibit, which router will be elected as the primary VRRP router?
- A. R2
- B. R4
- C. R3
- D. R1
Answer: D
NEW QUESTION # 109
Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?
- A. A local address must be specified.
- B. The BGP session type external must be specified.
- C. The BGP session type internal must be specified.
- D. A local AS must be specified.
Answer: A
NEW QUESTION # 110
Click the Exhibit.
On an MX Series device, you must enable routing between VLANs 100,200, and the Internet ge-5/1/0, and ge-5/1/2 are bundled into interface ae3. Ge-5/1/4, and ge-5/1/5 are bundles into interface ae2. Both AE bundles trunk VLANs 100 and 200.
In this scenario, what is the correct configuration snippet for VLAN 100?
- A. interfaces {xe-2/1/0 {unit 0{family inet {address 10.0.10.2/24;}}}ip-0/0/0 {unit 0 {family inet {address 10.0.1.2/24;}}unit 1 {family inet {address 10.0.2.2/24;}}}} bridge-domains {vlan- 100{domain-type bridge;vlan-id 100;interface ge-2/2/2.100;interface xe-2/1/0.0;interface ae1.100;interface ae3.100interface ip-0/0/0.0;}}
- B. interfaces {xe-2/1/0 {unit 0{family inter {address 10.0.10.2/24;}}}irb {unit 0{family inet {address 10.0.1.2/24;}}unit 1 family inet {address 10.0.2.2/24;}}}}bridge- domains {vlan- 100{domain-type bridge;vlan-id 100;interface ge-2/2/2.100;interface ae1.100;interface ae3.100;routing-interface irb.0;}}
- C. interfaces {xe-2/1/0{unit 0{family inet {address 10.0.10.2/24;}}}ip-0/0/0{unit 0{family inet {address 10.0.1.2/24;}}unit 1{family inet {address 10.0.2.2/24;}}}}bridge- domains {vlan- 100{domain-type bridge;vlan-id 100;interface ge-2/2/2.100;interface ae1.100;interface ae3.100;interface ip-0/0/0.0;}}
- D. interfaces {xe-2/1/0 {unit 0 {family inet {address 10.0.10.2/24;}}}irb {unit 0{family inet {address 10.0.1.2/24:}}unit 1 {family inet {address 10.0.2.2/24;}}}}bridge- domains {vlan- 100{domain-type bridge;vlan-id 100;interface ge-2/2/2.100;interface ae1.100;interface ae3.100;}}
Answer: D
NEW QUESTION # 111
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The BGP peering between R1 and R4 should use loopback interface addresses
- B. The BGP peerings between R1, R2, and R3 should use physical interface addresses
- C. The BGP peerings between R1, R2, and R3 should use loopback interface addresses
- D. The BGP peering between R1 and R4 should use physical interface addresses
Answer: C,D
NEW QUESTION # 112
Click the exhibit.
You are asked to enable a new BGP connection on R1, which has an existing IPv4 peering with R2. The new peering with R3 will use IPv6.
Referring to the exhibit, which two steps are required to enable the new IPv6 peering? (Choose two.)
- A. Configure an IPv6 address on the appropriate interface.
- B. Configure an IPv6 local address under the BGP group.
- C. Configure the rib inet6.0 statement under the BGP group.
- D. Configure an IPv6 neighbor address under the BGP group.
Answer: A,D
NEW QUESTION # 113
Click the Exhibit.
Referring to the configuration in the exhibit, which two statements are true? (Choose two.)
- A. The next-hop 172.16.1.2 must be part of an active route in route table inet 0 for route 192.168.5.0/24 to be active.
- B. The next-hop 172.16.1.2 must respond to ping commands for the route 192.168.5.0/24 to be active.
- C. The next-hop 172.16.1.2 must be directly connected to the router for route
- D. The next-hop 172.16.1.2 must be active in route table inet 3 for the route 192.168.5.0/24 to be active.
Answer: A,C
NEW QUESTION # 114
......
The JN0-363 exam focuses on the Junos OS, which is Juniper Networks' proprietary operating system for their networking equipment. Candidates are expected to have a solid understanding of the Junos OS and its features, as well as the ability to configure and troubleshoot various protocols and technologies such as MPLS, OSPF, BGP, and VPNs. Passing the JN0-363 exam demonstrates that a candidate has a high level of expertise in service provider routing and switching, making them an asset to any organization that relies on Juniper Networks' products and services.
100% Guarantee Download JN0-363 Exam Dumps PDF Q&A: https://www.dumpstorrent.com/JN0-363-exam-dumps-torrent.html
Kickstart your Career with Real Updated Questions: https://drive.google.com/open?id=1lt-QXrYZ8UZi9PJti0oIBYUbo3pXdmIj