[Sep 21, 2021] HPE6-A45 Dumps Full Questions - Exam Study Guide
Aruba Certified Switching Professional (ACSP) V1 Free Certification Exam Material from DumpsTorrent with 170 Questions
NEW QUESTION 18
Refer to the exhibit.
Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue. The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?
- A. asymmetric routing introduced by a routing protocol
- B. a jumbo frame mismatch
- C. mismatched subnet mask on the VLAN for the link
- D. an issue with VLAN mismatch
Answer: A
NEW QUESTION 19
Refer to the exhibit.
A company requires distribution layer switches that can provide Layer 2 and Layer 3 redundancy. The exhibit shows the proposal for these switches. Which change to the proposal will help meet the company's requirements?
- A. The proposed switches should be replaced with switches that support VSF to support the required distance between stack members.
- B. The proposed switches should be replaced with switches such as the Aruba 2930M to support the backplane stacking technology.
- C. VRRP should be implemented instead of backplane stacking to support the Layer 3 redundancy requirements.
- D. Link aggregations should be established without LACP to support the Layer 2 redundancy requirements and backplane stacking limitations.
Answer: D
NEW QUESTION 20
Refer to the exhibit.
The access layer AOS-Switches currently run DHCP snooping on VLAN 2 and connection rate filtering on edge ports. They are at default settings for ARP protection. A network administrator then enters these commands on each of the access layer switches:
Switch(config)# arp-protect vlan 2 Switch(config)# arp-protect
Which behavior accurse?
- A. The switches can now prevent ARP poisoning attacks and do not interfere with legitimate communications.
- B. The switches can prevent ARP poisoning attacks, but legitimate communications with VLAN 2 could also be disrupted.
- C. The switches will forward legitimate traffic and prevent ARP poisoning attacks, but interfere with connection rate filtering.
- D. The switches will not apply ARP protection due to interference from DHCP snooping, so the commands have no effect on current behavior.
Answer: A
NEW QUESTION 21
Refer to the exhibits.
Exhibit 2
The network administrator configures the commands shown in Exhibit 2. Which mismatch will cause an issue?
- A. the mismatch between the key-strings associated with VLAN 10 on Switch-1 and on Switch-2
- B. the mismatch between the chain names associated with VLAN 11 on Switch-1 and on Switch-3
- C. the mismatch between the key IDs specified in chain10 and chain11 on Switch-1
- D. the mismatch between the key-strings in the chains for VLAN 10 and VLAN 11 on Switch-1
Answer: A
NEW QUESTION 22
Network administrators decide to change OSPF Area 1 to a stub area in order to solve some performance issues. No routes are redistributed into area 1.
What is one implication of making this change?
- A. Endpoints in Area 1 will no longer be able to reach endpoints in other areas.
- B. Routing devices in area 1 will temporarily lose adjacency while the change is made.
- C. Endpoints in Area 1 will no longer be able to reach external networks.
- D. Routing devices in area 1 will no longer exchange Type 1 and Type 2 LSAs with each other.
Answer: C
NEW QUESTION 23
Refer to the exhibits.
Exhibit 1
Exhibit 2
Exhibit 2 shows IGMP groups on Switch-2, which runs IGMP but not PIM. Switch-1 and Switch-3 do not have IGMP or PIM enabled. Client 1 begins to forward multicasts to 239.1.1.1.
Which clients receive the multicasts?
- A. Client 2, Client 3, and Client 4
- B. Client 3 and Client 4, but not Client 2
- C. Client 3, but not any of the other clients
- D. Client 2, but not any of the other clients
Answer: D
NEW QUESTION 24
Exhibit
The exhibits show the current operational state for routes on Switch-3. The company wants Switch-3 to prefer the link to Switch-1 over the link to Switch-2 for all intra-area, inter-area, and external traffic. What can the network administrator do to achieve this goal?
- A. Set the OSPF administrative distance on Switch-2 higher than 110.
- B. Set the OSPF cost on VLAN 108 higher than 1 on Switch-2 and Switch-3.
- C. Set the OSPF area type to normal on all of the switches in Area 1.
- D. Set the cost in the OSPF Area 1 stub command higher than 1 on Switch-2.
Answer: D
NEW QUESTION 25
A network administrator needs to create a QoS policy on an AOS-Switch. What is one component that the administrator must create before the policy?
- A. a traffic class
- B. an extended IPv4 ACL
- C. an extended MAC ACL
- D. a traffic behavior
Answer: A
NEW QUESTION 26
A company has a wireless Aruba solution and wired users that connect to AOS-Switches.
The company wants
deep insight into the types of applications that wired users run. The company also wants more control over the traffic.
What can the company do to meet these goals?
- A. Configure extended IP ACLs on the AOS-Switches to filter the traffic.
- B. Set up remote traffic mirroring between the AOS-Switches and Aruba Mobility Controllers.
- C. Configure RMON receives on the switches.
- D. Use tunneled node to send traffic through an Aruba Mobility Controller
Answer: D
NEW QUESTION 27
Refer to the exhibits.
Exhibit 1
Exhibit 2
A company does not require authentication for security, but AOS-Switches are set up to use local MAC authentication (LMA) to assign the correct VLAN and priority to IP phones. IP phones and computers belong to different VLANs. Each device is supposed to connect to a specific port, but sometimes users connect their devices to the wrong ports and cannot receive access without help from IT.
How can a network administrator configure the switches to eliminate this issue?
- A. Add the MAC addresses for computers to the myPhones MAC group.
- B. Apply LMA to all edge switch ports, and set the unauth VLAN to the user VLAN.
- C. Create a user role that applies the user VLAN, and set this role as the initial role.
- D. Set the address limit to 2 on the switch ports that apply LMA.
Answer: A
NEW QUESTION 28
A company wants to implement RADIUS authentication of all managers who log in to AOS-Switches via SSH. The RADIUS server also sends VSAs that indicate which commands users can enter, and switches must honor these.
What must the administrator do to meet the company's requirements?
- A. Set command authorization to RADIUS, also set RADIUS for aaa authentication ssh login and aaa authentication ssh enable.
- B. Set RADIUS for aaa authentication ssh login and aaa authentication ssh enable, which allows the switch to accept all RADIUS VSAs.
- C. Set RADIUS for aaa authentication ssh login, also enable authentication privilege-login mode, which allows the switch to accept all RADIUS VSAs.
- D. Set the command access level to manager mode; also set RADIUS for aaa authentication ssh login and aaa authentication ssh enable.
Answer: C
NEW QUESTION 29
Refer to the exhibit.
Switch-1 runs BGP. What should the network administrator do to permit Switch-1 to establish a neighbor relationship with Router-1?
- A. Set the BGP AS number to 46501.
- B. Enable BGP on VLAN 100.
- C. Specify 192.168.1.0/30 with the network command in the BGP context.
- D. Configure 192.168.1.2 as a neighbor manually within the BGP context.
Answer: D
NEW QUESTION 30
Refer to the exhibit.
A network administrator sets up prioritization for an application that runs between Device 1 and Device 2.
However, the QoS for the application is not what the administrator expects.
How can the administrator check if the network infrastructure prioritizes traffic from Device 1 and Device 2?
- A. Set up RMON alarms on the switches that trigger when a high number of packets are dropped. Then, run the application and check for the alarm.
- B. Run a packet capture on Device 1, run the application, and look in the packet capture for a high value DSCP in the IP header.
- C. Clear interface statistics on the switches. Then, run the application and check the interface queue statistics for the switch-to-switch links.
- D. Run a packet capture on Device 2, run the application, and look in the packet capture for a high value DSCP in the IP header.
Answer: D
NEW QUESTION 31
Refer to the exhibits.
Exhibit 1.
Exhibit 2.
The exhibits show the current operational state for routes on Switch-3. The company wants Switch-3 to prefer the link to Switch-1 over the link to Switch-2 for all intra-area, inter-area, and external traffic.
What can the network administrator do to achieve this goal?
- A. Set the OSPF administrative distance on Switch-2 higher than 110.
- B. Set the OSPF cost on VLAN 108 higher than 1 on Switch-2 and Switch-3.
- C. Set the OSPF area type to normal on all of the switches in Area 1.
- D. Set the cost in the OSPF Area 1 stub command higher than 1 on Switch-2.
Answer: D
NEW QUESTION 32
Refer to the exhibits.
Exhibit 1
Exhibit 2
Network administrators are alerted to high interface utilization on a switch by a management solution. They examine the utilization on the uplink interfaces several times an hour during problem times. The exhibit shows output typical of times of congestion. The administrators want to allocate bandwidth fairly and reduce congestion on the uplinks.
What could help meet these requirements?
- A. an outbound rate limit on interfaces 1 and 2
- B. an outbound rate limit on each edge port
- C. a per-queue rate limit on interfaces 1 and 2
- D. a broadcast rate limit on each edge port
Answer: D
NEW QUESTION 33
Refer to the exhibit.
AOS-Switches will enforce 802.1X authentication on edge ports. The company has two RADIUS servers, which are meant to provide redundancy and load sharing of requests.
The exhibit shows the planned RADIUS settings to deploy to the switches.
What should customers understand about this plan?
- A. AOS switches do not support two RADIUS servers for redundancy, instead, a secondary authentication method is required.
- B. Each RADIUS server must use a unique port number for the authentication and dynamic authorization port.
- C. Each AOS-Switch will send all RADIUS requests to the first server on the list unless that server becomes unreachable.
- D. Dynamic authentication is only permitted on one of the RADIUS servers and must be removed from the other.
Answer: C
NEW QUESTION 34
Refer to the exhibit.
A company requires distribution layer switches that can provide Layer 2 and Layer 3 redundancy. The exhibit shows the proposal for these switches. Which change to the proposal will help meet the company's requirements?
- A. The proposed switches should be replaced with switches that support VSF to support the required distance between stack members.
- B. The proposed switches should be replaced with switches such as the Aruba 2930M to support the backplane stacking technology.
- C. VRRP should be implemented instead of backplane stacking to support the Layer 3 redundancy requirements.
- D. Link aggregations should be established without LACP to support the Layer 2 redundancy requirements and backplane stacking limitations.
Answer: D
NEW QUESTION 35
Refer to the exhibits.
Exhibit 1
Exhibit 2
A network administrator wants to set up mirroring of traffic from port 1 on Switch-1 to port 1 on Switch-2. Exhibit-2 shows the commands that the administrator enters. The mirroring does not work correctly.
What must the administrator do to correct the error?
- A. Remove the commands and re-enter them on Switch-1 first and then on Switch-2.
- B. Re-configure the mirror endpoint command on Switch-2 with the IP addresses reversed in order.
- C. Change the port ID on Switch 1 to 50001, so that it is unique from the port ID on Switch-2.
- D. Specify the mirror endpoint command in Switch-1 and the mirror 1 remote-ip command on Switch-2.
Answer: B
NEW QUESTION 36
......
Dumps Brief Outline Of The HPE6-A45 Exam: https://www.dumpstorrent.com/HPE6-A45-exam-dumps-torrent.html